Programmer

The SF100 is a high speed "In System Programming" programmer to update the SPI Flash soldered on board or Freescale MCU using Ezport. The programmer is easily controlled by the computer DediProg Software through the USB bus offering friendly interface and powerful features to users.

Specification

Features :

USB Interface

Start button feature

Signal conflict protections

Update Serial Flash soldered on board with application powered or not

Control Application, controller reset and MOSFET isolation status

Update the internal Flash of Freescale MCU using the Ezport (MCF5223,MCF5221,MCF5213) or the external SPI Flash of Freescale MCU using the SBF interface (MCF5445, MCF5227)

Capable of handling two serial flash memories (new feature; provided in SF100 with serial number DP001325, firmware 2.0.4, software 2.0.37 and after)

Multi-Programmers Capability

Support Windows 2003 and above

Support both 32 bit or 64 bit OS

Support 1 CS pin

The SF100 USB software tool chain offers high flexibility and fit the different and highest requirements:

Engineering Graphic User Interface:
For engineers and expert to access advanced features for development, repairing etc.

Production Graphic User Interface:
For operators in production to control multiple programmers and improve the throughput.

Command line interface:
Customer software can control the multi SF100 programmers (SF100 integration, Control SF100 with Production In Circuit Tester..)

High performance:

USB Mode	Memory size
Reference IC	W25X80VSSIG	W25Q16VSSIG	W25Q32VSSIG	W25Q64FVSSIG	W25Q128BVFIG	W25Q256FVFIG	S25FL512SAGMFI011
Density	8Mb	16Mb	32Mb	64Mb	128Mb	256Mb	512Mb
(Program + Verify)	11s	15s	20.5s	48.5s	94s	157s	297s

*Please note the programming and verify time will depends on different IC type; please refer to the IC specification before programming.

Hardware :

SF100 is designed with ISP header, through an appropriate connector; users can connect the programmer and drive the SPI signals, supply the memory and control the controller or application status. Please refer to Table 1 for the SF100 2x7 header pin out. DediProg also provides the SF100 ISP Cable which is used to connect the SF100 programmer to the 2X4 2.54mm ISP Pin Header on board, please refer to Table 2 for the SF100 ISP Cable 2x4 pin out.

Table 1: SF100 ISP Header Pin Out (2x7)

1	I/O1	I/O4	2
3	I/O2 or CS2	NC	4
5	Vcc	GND	6
7	CS	CLK	8
9	MISO	MOSI	10
11	Vpp/Acc	I/O3	12
13	SCL	SDA	14

Table 2: ISP Cable Connector Pin Out (2x4)

1	Vcc	GND	2
3	CS	CLK	4
5	MISO	MOSI	6
7	Vpp/Acc	I/O3	8

Contents :

SF100 Programmer*1

USB cable*1

ISP cable*1

SF100 Universal Adaptor*1

CD-ROM*1(Included Software, specifications and user manual)

Hardware Requirement for ISP :

To have a clear understanding on the different ISP or backup boot methods and different reference schematics, please download our dedicated application notes: AN0103 and AN0106 in the documentation section [Download]

Option Purchase :

Backup Boot Flash-SO8N
Backup Boot Flash-Dual SO8N
Backup Boot Flash-SO8W
Backup Boot Flash-Dual SO8W

Backup Boot Flash-SO16W
Backup Boot Flash-Dual SO16W
BBF SO8 Testclip
BBF SO8 Testclip-Dual

BBF SO16W Testclip
ISP SO8 Testclip
ISP SO16W Testclip
SF100 Universal Adaptor

Next SF600 SPI Flash IC Programmer