Programmer

The SF600 is a high speed "in System Programming" programmer to update the SPI Flash soldered on board (In Circuit Programming) or in the socket adaptor (Off line programming). The programmer is easily controlled by the computer DediProg Software through the USB bus offering friendly interface and powerful features to users.
SF600 combines the advantages of SF100 with additional improvements: High speed USB and higher SPI performances.
Specification

 Features :

  • USB High speed and high SPI performance, support up to 2Gb SPI Flash
  • In circuit Programming: Program on board SPI Flash
  • Off line Programming: Program SPI Flash in the socket
  • Program two Serial Flash memories
  • Start button feature: Able to Batch in the USB mode
  • Signal conflict protections
  • Multi-Programmers Capability through USB
  • Support 1.8V low voltage IC
  • Support Windows 2003 and above
  • Support both 32 and 64 bit OS
  • Support 1 CS pin

    The SF600 USB software tool chain offers high flexibility and fit the different and highest requirements:

    Engineering Graphic User Interface:
    For engineers and expert to access advanced features for development, repairing etc.
    Production Graphic User Interface:
    For operators in production to control multiple programmers and improve the throughput.
    Command line interface:
    Customer software can control the multi SF600 programmers (SF600 integration, Control SF600 with Production In Circuit Tester.)


    High performance(25MHz, Single IO):

    USB Mode

    Memory size

    Reference IC W25X80VSSIG W25Q16VSSIG W25Q32VSSIG W25Q64FVSSIG W25Q128BVFIG W25Q256FVFIG S25FL512SAGMFI011
    Density 8Mb 16Mb 32Mb 64Mb 128Mb 256Mb 512Mb
     (Program + Verify) 9s 11.6s 12.6s 31s 61.7s 89.2s 147.4s

    *Please note the programming and verify time will depends on different IC type; please refer to the IC specification before programming.


    Hardware :

    SF600 is designed with ISP header, through an appropriate connector, users can connect the programmer and drive the SPI signals, supply the memory and control the controller or application status. Please refer to Table 1 for the SF600 2x10 header pin out. DediProg also provides the SF600 ISP Cable which is used to connect the SF600 programmer to the 2X6 2.54mm ISP Pin Header on board, please refer to Table 2 for the SF600 ISP Cable 2x6 pin out.

    Table 1: SF600 ISP Header Pin Out (2x10)
    1 Vpp CS2 2
    3 CS1 Vcc 4
    5 MISO/DQ1 Hold/DQ3 6
    7 Wp/DQ2 CLK 8
    9 GND MOSI/DQ0 10
    11 NC Reset/IO3 12
    13 NC NC 14
    15 NC NC 16
    17 NC NC 18
    19 GPIO1 GPIO2 20
    Table 2: ISP Cable Connector Pin Out (2x6)
    1 Vpp CS2 2
    3 CS1 Vcc 4
    5 MISO/DQ1 Hold/DQ3 6
    7 Wp/DQ2 CLK 8
    9 GND MOSI/DQ0 10
    11 NC Reset 12

    Contents :

    • 1 x SF600 Programmer
    • 1 x USB Cable
    • 1 x ISP Cable (ISP-600-CB1-G)
    • 1 x SF100 2.54mm 2*4 ISP Cable (ISP1-CB)
    • 1 x SF600 Universal Adaptor (ADP-SF600-TO-SF100)
    • 1 x CD-ROM (Included Software, specifications and user manual)

    Hardware Requirement for ISP :

    To have a clear understanding on the different ISP or backup boot methods and different reference schematics, please download our dedicated application notes: AN0103 and AN0106 in the documentation section.[Download]


    Option Purchase :

    • Backup Boot Flash-SO8N
    • Backup Boot Flash-Dual SO8N
    • Backup Boot Flash-SO8W
    • Backup Boot Flash-Dual SO8W
    • Backup Boot Flash-SO16W
    • Backup Boot Flash-Dual SO16W
    • BBF SO8 Testclip
    • BBF SO8 Testclip-Dual
    • BBF SO16W Testclip
    • ISP SO8 Testclip
    • ISP SO16W Testclip
    • SF100 Universal Adaptor 
^