Programmer

The SF600 is a high speed "in System Programming" programmer to update the SPI Flash soldered on board (In Circuit Programming) or in the socket adaptor (Off line programming). The programmer is easily controlled by the computer DediProg Software through the USB bus offering friendly interface and powerful features to users.
SF600 combines the advantages of SF100 with additional improvements: High speed USB and higher SPI performances.

Specification

Features :

USB High speed and high SPI performance, support up to 2Gb SPI Flash

In circuit Programming: Program on board SPI Flash

Off line Programming: Program SPI Flash in the socket

Program two Serial Flash memories

Start button feature: Able to Batch in the USB mode

Signal conflict protections

Multi-Programmers Capability through USB

Support 1.8V low voltage IC

Support Windows 2003 and above

Support both 32 and 64 bit OS

Support 1 CS pin

The SF600 USB software tool chain offers high flexibility and fit the different and highest requirements:

Engineering Graphic User Interface:
For engineers and expert to access advanced features for development, repairing etc.

Production Graphic User Interface:
For operators in production to control multiple programmers and improve the throughput.

Command line interface:
Customer software can control the multi SF600 programmers (SF600 integration, Control SF600 with Production In Circuit Tester.)

High performance(25MHz, Single IO):

USB Mode	Memory size
Reference IC	W25X80VSSIG	W25Q16VSSIG	W25Q32VSSIG	W25Q64FVSSIG	W25Q128BVFIG	W25Q256FVFIG	S25FL512SAGMFI011
Density	8Mb	16Mb	32Mb	64Mb	128Mb	256Mb	512Mb
(Program + Verify)	9s	11.6s	12.6s	31s	61.7s	89.2s	147.4s

*Please note the programming and verify time will depends on different IC type; please refer to the IC specification before programming.

Hardware :

SF600 is designed with ISP header, through an appropriate connector, users can connect the programmer and drive the SPI signals, supply the memory and control the controller or application status. Please refer to Table 1 for the SF600 2x10 header pin out. DediProg also provides the SF600 ISP Cable which is used to connect the SF600 programmer to the 2X6 2.54mm ISP Pin Header on board, please refer to Table 2 for the SF600 ISP Cable 2x6 pin out.

Table 1: SF600 ISP Header Pin Out (2x10)

1	Vpp	CS2	2
3	CS1	Vcc	4
5	MISO/DQ1	Hold/DQ3	6
7	Wp/DQ2	CLK	8
9	GND	MOSI/DQ0	10
11	NC	Reset/IO3	12
13	NC	NC	14
15	NC	NC	16
17	NC	NC	18
19	GPIO1	GPIO2	20

Table 2: ISP Cable Connector Pin Out (2x6)

1	Vpp	CS2	2
3	CS1	Vcc	4
5	MISO/DQ1	Hold/DQ3	6
7	Wp/DQ2	CLK	8
9	GND	MOSI/DQ0	10
11	NC	Reset	12

Contents :

1 x SF600 Programmer
1 x USB Cable
1 x ISP Cable (ISP-600-CB1-G)
1 x SF100 2.54mm 2*4 ISP Cable (ISP1-CB)
1 x SF600 Universal Adaptor (ADP-SF600-TO-SF100)
1 x CD-ROM (Included Software, specifications and user manual)

Hardware Requirement for ISP :

To have a clear understanding on the different ISP or backup boot methods and different reference schematics, please download our dedicated application notes: AN0103 and AN0106 in the documentation section.[Download]

Option Purchase :

Backup Boot Flash-SO8N
Backup Boot Flash-Dual SO8N
Backup Boot Flash-SO8W
Backup Boot Flash-Dual SO8W

Backup Boot Flash-SO16W
Backup Boot Flash-Dual SO16W
BBF SO8 Testclip
BBF SO8 Testclip-Dual

BBF SO16W Testclip
ISP SO8 Testclip
ISP SO16W Testclip
SF100 Universal Adaptor

Pre SF100 ISP IC Programmer Next SF600 Plus SPI Flash IC Programmer